1-20 of 45
Keywords: turning (machining)
Close
Sort by
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. October 2011, 133(5): 051009.
Published Online: October 17, 2011
... 10 2011 decision making turning (machining) Scientists and engineers often expend considerable effort in performing measurements and developing models to predict the results of future experiments. These are naturally significant activities...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. August 2011, 133(4): 041010.
Published Online: August 11, 2011
... crystal morphology cutting tools deformation finite element analysis mechanical engineering computing solid modelling thermomechanical treatment turning (machining) hard turning chip morphology cutting parameters tool geometry finite element simulation Saw-tooth chip commonly...
Journal Articles
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Manuf. Sci. Eng. December 2010, 132(6): 064501.
Published Online: October 14, 2010
... ). rolling bearings shear modulus turning (machining) 02 12 2008 27 06 2010 14 10 2010 14 10 2010 2010 American Society of Mechanical Engineers ...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. October 2010, 132(5): 051007.
Published Online: September 22, 2010
... turning (machining) Gradual tool wear prediction has been typically approached using empirical models. The applicability of the empirical models such as Taylor’s equation ( 1 ) is very limited especially when the performance of a new tool on a potential work material is needed. Physics-based...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. August 2010, 132(4): 041015.
Published Online: August 3, 2010
... (approximate Gaussian nature) and enabled the use of less elaborate tool health assessment methods. condition monitoring drilling grinding inspection maintenance engineering milling quality control turning (machining) 06 01 2009 03 06 2010 03 08 2010 03 08 2010...
Journal Articles
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. April 2010, 132(2): 021002.
Published Online: March 26, 2010
... sample using the scattering measurement system, and then with a NT3300 Veeco optical profilometer. The machining reported in this paper was performed on a 350FG freeform generator (Fig. 3 ), an ultraprecision diamond turning machine with three linear axes. The diamond turning machine is also...
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Manuf. Sci. Eng. December 2009, 131(6): 064506.
Published Online: December 4, 2009
... 04 12 2009 04 12 2009 coolants cutting tools environmental factors life testing manufacturing systems steel surface finishing surface roughness titanium compounds turning (machining) Weibull distribution machining green manufacturing tool life finish turning...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. December 2009, 131(6): 061005.
Published Online: November 10, 2009
... fixtures to improve stiffness ( 18 ). lathes open loop systems piezoelectric actuators sliding friction surface texture surface topography turning (machining) vibration control wear 06 04 2009 20 09 2009 10 11 2009 10 11 2009 Cross sectioned dimple...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. August 2009, 131(4): 041005.
Published Online: July 8, 2009
.... Eng. Ind. 0022-0817 , 111 ( 2 ), pp. 37 – 47 . 29 07 2008 27 04 2009 08 07 2009 cutting cutting tools damping machine tool spindles machining chatter mechanical stability turning (machining) vibrations chatter turning stability The productivity...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. August 2009, 131(4): 041004.
Published Online: July 8, 2009
... that should be accounted for by elliptical curve fitting. Residual stresses by grinding show more scattering than those by hard turning. Machining is the deterministic factor for the resulting residual stress magnitudes and profiles compared with the minor influence of initial residual stress by heat...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. December 2008, 130(6): 061007.
Published Online: October 10, 2008
... observations, with average relative errors of 11.6% and 7.2%, respectively. 09 02 2008 08 08 2008 10 10 2008 elasticity rings (structures) turning (machining) Surface form errors are ubiquitous in material removal processes and are well documented in the literature. Surface...
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Manuf. Sci. Eng. October 2008, 130(5): 054503.
Published Online: September 11, 2008
... cutting tools ductility iron quenching (thermal) surface roughness turning (machining) wear austempered ductile iron tool wear cutting forces surface roughness CBN machinability Austempered ductile iron (ADI) has recently been developed for an increasing number of the engineering...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. August 2008, 130(4): 041004.
Published Online: July 8, 2008
... that was used for machining to submicrometer levels. The significant error sources identified in the machining process were thermal effects and deflections of the structural loop of the diamond turning machine (DTM) that led to registration errors of the cutting tool between consecutive passes. Environmental...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. June 2008, 130(3): 031002.
Published Online: May 2, 2008
... algorithm, in terms of total machining time and required computational time, is superior to an exhaustive search algorithm. 23 04 2007 24 10 2007 02 05 2008 particle swarm optimisation search problems turning (machining) Determining the optimal process parameters...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. October 2007, 129(5): 893–901.
Published Online: March 29, 2007
.... cutting cutting tools failure analysis tungsten compounds cobalt finite element analysis coatings turning (machining) design engineering Based on the enhanced modeling methodology extended to include coatings, microstructure-level finite element simulations of continuous orthogonal cutting...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. August 2007, 129(4): 733–739.
Published Online: March 14, 2007
... formulation reduces to a one-dimensional (1D) expression for boring stability predictions. chatter insert nose model turning stability boring stability boring mechanical stability turning (machining) machining chatter cutting cutting tools 01 06 2006 14 03 2007 2007...